The same household calls about the same jammed disposal two or three times, because nobody ever showed them the wrench.
It's in a drawer somewhere. It came in the box when the unit was installed, and it's a small hex key shaped specifically to fit a socket in the base of the machine. With it, freeing a jam takes about ninety seconds. Without it — or without knowing it exists — a jam is a callout.
Same with the reset button. A red button on the underside that pops out when the motor overloads, cutting all power until it's pushed back in. A meaningful share of "dead" disposals are simply waiting for someone to reach underneath.
Neither is complicated. Neither is dangerous, done properly. And both account for a large share of the calls in this category.
So we show you. Where the wrench is or what to use instead, where the reset button sits, and how to do it safely — so the next one costs you nothing.
Tap the call button and tell us what it's doing.
TrueFlow Plumbing repairs, replaces, and installs garbage disposals across Cimarron Hills, CO for homes and businesses.
Demonstrated properly, not described.
Freeing a Jam
The symptom — it hums but won't turnPower is reaching the motor and something is wedged between the impellers and the grind ring.
The Reset Button
The symptom — complete silence, no response at allBecause knowing it once isn't the same as remembering it in a year.
Or a replacement supplied if yours is missing. Somewhere it can't get lost in a drawer.
So you've seen where it is rather than been told.
Which speeds up any future parts decision.
Humming means jam. Silence means power. Two sentences that cover most of what goes wrong with these.
Humming without turning — switch off at the wall, then the wrench from underneath.
Complete silence — the reset button, then the breaker, then the plug.
Either of these may be your whole answer, and we'll walk you through it on the phone.
The mounting flange seal has failed. A reseat — a repair, not a replacement.
The discharge outlet or the dishwasher connection — a hose, a clamp, or a gasket.
Water from the body means internal seals have failed and water has been inside the motor. These are sealed assemblies not designed to be opened. That unit is finished.
So "it's leaking" isn't a diagnosis. Two of three positions are inexpensive fixes; one is a replacement — and it's worth knowing which before anyone quotes.
The unit is doing its job and the waste has nowhere to go — the trap or the line beyond is blocked, usually with grease. Replacing the disposal changes nothing here. It's drain work.
Which confirms the problem is past the disposal.
Frequently the knockout plug in the dishwasher inlet, which has to be removed at installation and sometimes isn't. A two-minute fix.
Say this on the call — it changes what we bring, and it stops you paying for a replacement that wouldn't have helped.
And one worth saying: if yours has failed and you rarely used it, a plain waste and trap is cheaper, simpler, and one less thing to go wrong.
Mostly avoidable, and worth knowing alongside the wrench.
Being run against a jam. The single most common self-inflicted failure, and it takes seconds.
The wrench, the reset button, and the two symptoms that tell them apart. Ninety seconds each, demonstrated rather than described.
Taped under the sink, not lost in a drawer — or replaced if yours has gone.
If a jam or a reset is your whole answer, you keep your money and we don't take a booking we didn't need.
Top, side, or bottom. Two are repairs and one is a replacement.
A disposal grinding perfectly while the sink fills is not a disposal fault.
If you rarely used it, a plain waste and trap is cheaper and simpler.
Licensed, insured, and background-checked plumbers serving Cimarron Hills, CO.
You'll have the diagnosis and the options before work begins — and the tools and knowledge to handle the common ones yourself afterwards.
TrueFlow Plumbing proudly serves Cimarron Hills, CO and the surrounding neighborhoods, repairing, replacing, and installing garbage disposals for domestic and commercial properties throughout the area. Unsure whether you're in range? Call and ask.
Click Here To Call Number(833) 435-3258That's a jam. Switch it off at the wall immediately — running against a jam is what actually burns these units out, and it takes seconds. Then fit the hex wrench into the socket in the base and work the plate back and forth until it turns freely.
It came in the box with the unit and it's usually in a drawer somewhere. If it's lost, a replacement costs almost nothing from any hardware shop — or a wooden spoon handle levered against an impeller from above does the same job.
The reset button on the underside — it pops out when the motor overloads and cuts all power until pushed back in. Most people don't know it's there, and it accounts for a real share of "dead" disposals. If it's already in, check the breaker and whether the unit is plugged in.
No. Tongs or long-nosed pliers with the power off at the wall, or free it with the wrench from underneath. There's no version where reaching in is the right move.
Not with the power off at the wall and the right tool. The wrench works from underneath, so nothing goes into the chamber at all. It's the one part of plumbing where the manufacturer supplies the tool expecting you to use it.
Honestly, because it's a repeat callout otherwise. We'd rather have the calls that genuinely need us — leaking housings, blocked drain lines, replacements — than the ones a ninety-second demonstration prevents.
Depends where from. From the top where it meets the sink is the flange seal — a reseat. From the side is a discharge or dishwasher connection. From the bottom of the housing means water has been in the motor, and that one is a replacement.
Then it isn't the disposal. The trap or the line beyond is blocked, and replacing the unit wouldn't fix it. Different job, and worth saying on the call.
Yes, despite what you may have heard. Grounds settle downstream as a dense sludge. Eggshell membranes wrap the impellers and the shell becomes a grit that accumulates.
Cold, always, and running well after you've finished. Hot water melts fats so they travel further before setting.
Several years with reasonable use, considerably longer if it's never run against a jam. That single habit is the difference between a unit that lasts and one that doesn't.
Not necessarily. If yours has failed and you rarely used it, a plain waste and trap is cheaper, simpler, and one less thing to go wrong.
A hex wrench in a drawer and a red button under the machine account for most of what goes wrong with these — and both are ninety-second jobs once you've been shown. The reason people call twice is that nobody demonstrated it the first time.
TrueFlow Plumbing walks you through the checks on the phone, shows you the wrench and the reset button in person, leaves the wrench somewhere you'll actually find it, and would rather have the calls that genuinely need a plumber.
Tap the call button and tell us what it's doing — humming, silent, leaking, or backing up.
Click Here To Call Number(833) 435-3258